Approach-tech DVR-3016 Uživatelský manuál

Before trying to connect or operate this product, please read this manual completeINSTALLATION &OPERATING MANUALDigital Video RecorderDVR-3016 &am

815 call button: If you connect to the call monitor, the "Call" button enables you to select channels on this monitor. Press the "Cal

9 2.2 Rear View 2930 75Ω/Hi-Z Individual termination: These 16 switches are used to set the impedance of each loop through output con

102.3 ALARM In/Out The pin assignment of the female DB-25 alarm I/O connector is listed as follows. alarm I/O12345678910111213141516171819202122232

113. INSTALLATION Please follow the instructions and the diagram below to set up the system. 3.1 Basic Connection CONNECTING WITH 1 to 16

123.2 Hard-Disk Drive Installation The 16CH DVR is equipped with two compartments of hard-disk drives and a CD-RW drive (FOR CD-ROM MODEL ONLY). Th

133.3 HDD Information and channel selection 3.3.1 HDD information You can display the HDD information as shown on Figure 3.3 A below at any time b

143.4 Updating System Software If the system software of the 16CH DVR needs to be upgraded, please take the following steps to safely update it.

154. BASIC OPERATIONS This section shows you how to operate and manage the DVR. 4.1 Recording Operations This section details the way to recor

16NOTE: You can proceed to start the scheduled recording from the current time if it is in the scheduled interlude as soon as the setting is complete

17 ADVANCED SETTING 1 ALARM SETTING: ENTER 2 RECORD SETTING: ENTER 3 MOTION SETTING: ENTER 4 CAMERA COVERT: ENTER 5 OPERATION LOCK: ENT

184.1.3 Alarm Recording Take the following steps to activate the programmed alarm recording. For ALARM settings, please refer to section 5.6.1 for

194.1.4 Externally triggered Recording By connecting the RECORD IN of ALARM I/O on the rear panel of the DVR, you can activate/deactivate the

20 4.2 Playback Operations This section shows you how to operate the fast, slow, and single-picture playback functions, and details how the unit is

21 4.2.3 Playback Picture-by-picture While playing back recorded video at the recorded speed: (1) Press the PAUSE button for the picture-by-pi

224.3 Search Operations This section shows you how to access recorded video. 4.3.1 Full List Search Take the following steps to proceed wit

23 (“CD” IS FOR THE CD-ROM MODEL AND “BACKUP” IS FOR THE REMOVABLE HDD MODEL ONLY IN THE ITEM 6.) 4.3.3 SEARCH FILTER Take the following s

24 4.3.4 THUMBNAIL Search Take the following steps to proceed with the thumbnail search function. (1) Press the Search button to enter the search

25 (“CD” IS FOR THE CD-ROM MODEL AND “BACKUP” IS FOR THE REMOVABLE HDD MODEL ONLY IN THE ITEM 6.) 4.3.6 CD (BACKUP) Menu 4.3.6.1

264.3.6.2 BACKUP Menu (FOR HARD-DISK MODEL ONLY) Please refer to section 4.4.2 “Mobile Rack HD Backup Operations” for more details. 4.4 Back

27to view your selections. 4. CD AVI: You can archive a video in the CD disc by entering this item. Please follow the steps given below. i )

1 All the following safety and operation instructions for the prevention of harm or damage to the operator or other persons should be read before the

28 (2) Backup to HD3.  Press the “Search” button and enter the SEARCH page.  Move the focus to BACKUP and enter the BACKUP MENU page.  Set the

294.4.3 Security Digital Card (SD Card) Backup Operations The SD card slot of the front unit has four functions as shown below: 1. Archive Single i

30 SAVE AVI0001.AVI TO SD CARD SAVE AVI0002.AVI TO SD CARD … SAVE AVI000N.AVI TO SD CARD NOTE: ●The JPEG file format can be pl

31 4.5 Key Lock Operations ● To activate the key lock function. (1) Press the Menu button to enter the MAIN MENU page. (2) Select ADVANCE SETTING

324.6 Triplex Operations 4.6.1 Live mode: ● Simultaneous live viewings of any one channel in multiple channels. (1) Use the enter button to show a

335. MENU SETUP There are 9 functional items for operation setting in the setup menu system as shown below. The following sections will instruct you

345.1 QUICK SETTING This page enables you to rapidly install your desired setting. For more detailed changes, enter each item page. 1. TIME SETTI

355.2 DISPLAY OPTION This item enables you to fix the display labels on your screen. 1. TIME MODE: You have a choice between using a 12 HR or a 24 H

362. TIME DISPLAY COLOR: You can choose between red, yellow, blue, green, black, and white. 3. DATE DISPLAY: Select to ON or OFF as desired. 4. DATE

37 9. DAYLIGHT SAVING SETTING: This entry allows users to set the daylight saving time. 1. NONE: Disables the daylight saving time. 2

2Table Of Contents 1. PRODUCT FEATURES ... 4 1.1 Produ

385.3 SEQUENCE SETTING This page enables you to use ten modes to set the sequence of displays you want for the main monitor, and a single mode for th

395.4 PICTURE ADJUST This page enables you to position your images the way you desire. 1. H POSITION: Horizontal position. 2. V POSITION: Vertic

405.6 AVANCED SETTING This page includes multiple special functions. 5.6.1 ALARM SETTING This page enables you to set all the various alarm - relat

41 4. ALARM RECORD RATE: For an NTSC unit we provide many different speeds from 0 to 60 fields per second, and for a PAL unit the figures are from 0

421. RECORD QUALITY: You can enter and set each channel's record quality at 4 different levels of image recording from "BEST","HI

435.6.4 COVERT CAMERA Enter and activate each channel to ON or deactivate to OFF for hidden or exposed recording respectively. 5.6.5 OPERATION LO

445.6.6 COMMUNICATION We provide you with two settings: the RS 232 and RS 485. 1. RS-232 SETTING: You have the option of using an ID code ( any num

455.6.7 DISK SETUP Enter the disk mode to select your desired setting. 1. DISK FULL: This option determines the way to utilize storage media in case

469. RETURN: Go back to the previous page. 5.6.8 SCHEDULE Enter the setting to set up 8 forms of schedule. A schedule can change the record settin

478. RETURN: Go back to the previous page. 5.6.9 RETURN To exit the “ADVANCED SETTING” page choose “RETURN” and go back to the “MAIN MENU” page. 5.

35.2 DISPLAY OPTION...35 5.3 SEQUENCE

48 5.8 PASSWORD SETTING This page enables you to set the password. 1. MENU PASSWORD. This option lets you set a password to block any unauthorized

495.9 EXIT MENU If you wish to exit the menu, focus on this item and enter. 1. EXIT MENU WITHOUT SAVING: Enter to exit at once without saving any s

506. NETGUARD SYSTEM: Introduction NETGUARD SYSTEM : This version of the NETGUARD SYSTEM uses the Microsoft .Net Framework version. The .Net Framewo

516.1 TCP/IP Communication Setup Follow the instructions below to install the TCP/IP communication program into your computer. 1. Click the Start Me

523.Click on the Configuration tag; check if the TCP/IC is included among the network components list. If the TCP/IP is included, please process step

535 TCP/IP Configuration setting  Click Start  Control Panel  Network.Connections  Local Area Connection  Select Internet Protocol (TCP/IP), and

546.2 Connection Testing With the previous settings, follow the instructions below to ensure whether you have established the connection successfull

554. If you receive a response as in the sample screen below, you have successfully made the connection. 6.3 Software installation. Step

56Step 4: The installation screen will show the message "C :\ Program Files \ NETGUARD \". Or you can select the path you want.

57Step 6 : After completing installation, you can double - click the file shown below. Or click the "Start Menu" in the computer and select

41. PRODUCT FEATURES 1.1 Product Introduction This 16CH DVR is a triplex digital recorder with a 16ch multiplexer, capable of Triplex simultan

586.4 Short introduction Once the NETGUARD is executed, a log in window will appear. Please type the appropriate user name and password to log into t

59 【Multiscreen】：Here all the videos of the cameras will show. 【Multiscreen Buttons】：You can interchange between three buttons here : the "Vid

60 1. Adjust the screen size: Move the mouse to the vertical bar on the right side of the "Work Devices" / "Available Devices"

61 "Print": Click the "Print Preview" button and go to the "Preview" option to adjust the image size. Go to the "

62 6.5.2 Remote play and PTZ control. This device has the full triplex so you can use the NETGUARD in the remote without affecting the performance of

63the way, without stopping, in one of the four designated directions. The fifth button, in the center, will stop the camera at any point you prefer.

64● Frame dimension : Sets the resolution. ● Mark Day and Time : Sets the date and time stamp. Play Options： ● Time to play : To search the date a

65 6.5.4 Web Page Viewer This section provides instructions for using the NETGUARD's web page viewer feature. 1. " Click "PTZ Devic

66● Image: Click "Image" to enter the "Image " page to set each channel's "Channel Title", "Quality", &

672. "Playback Record Time". Click the "Display Mode" to select from a drop - down list of two choices, "Hide" and &quo

5each camera). ＊ Selectable display position and color of title/time/date OSD text in both MAIN and CALL monitors. ＊ Covert camera recording. ＊ Sc

686.6 The Image Viewer The 16CH DVR is equipped with a digital watermark. It's a check software which protects archived images and informs you

697. Microsoft Internet Explorer This section provides instructions for accessing the 16CH DVR via Microsoft Internet Explorer. Connecting the 1

70 Function Buttons Description Stop- Click to stop playing back the recorded video or to cease recording. / Pause / Play- Click to a recorded v

71 Image display area. Displays images from the 16ch cameras. " Click "PTZ Device" to open the control panel and remote control the

728. SPECIFICATIONS Model DVR 3016 DVR 3016D Resolution NTSC 720x240 pixels; PAL 720x288 pixels Operation Mode Triplex (Live, Play, Record and

73APPENDIX 1. – RS-232 & RS-485 Codes RJ-11 PIN configuration for RS-485 PIN NO. PIN Assignment 1. Not Connected 2. Ground 3. D - 4. D + 5. Gr

74Separation Code A separation code is used to insert between two control command codes to ensure a proper operation. They do not have any explicit f

75d Same as display button f Same as freeze button b Same as search button z Same as zoom button j Same as jog+ button k Same as jog- b

76R10/ Selects “CH10” to display under PIP, Quad, 2x2, 3x3, or 4x4 format R11/ Selects “CH11” to display under PIP, Quad, 2x2, 3x3, or 4x4 format R

77? Status inquiry: This code is used to inquire the operating status of a specific unit in the system. The addressed unit will response with

62. DESCRIPTION OF THE FRONT/REAR VIEW 2.1 Front View FOR CD-ROM MODEL 1 CD-RW device compartment: The compartment allows you to b

78APPENDIX 2. – Using CD Discs (FOR CD-ROM MODEL ONLY) Please note that when using CD-ROM, CD-R and CD-RW discs, do not write or stick anything on t

79Emergency Eject Button The device has an emergency eject button, which allows for manual retrieval of the disc in case the machine needs repair, o

7 5 Jog Dial: This dial can act in both a forward and a backward direction, as well as step by step. Turn this left to play a recorded video in the